Would like to do a front and rear end swap on the 900. The front end swap is fairly straight forward but I am not so sure on the rear. The zzr1100 rear swingarm only pivots at the frame but the 900r uses the motor as well. is it a case of just cutting the middle section out and adding the right bushes and bearings ? . Any help would be great.
A tape measure is your friend , nothings Impossable if you throw enough time money and skinned knuckels at it. Might be a good idea to drop into the intro area and drop a little line as to your story before the sharks start to turn up. Questions are fine but people like a little courtesy around these parts. Info's free for people happy to say hi before asking the orical for input.
You will prob find the stock swing arm will take a wider rim/tyre package if you want an easyer way out. The later 900's were 150 tyre stock so a 180 or 190 will prob squeeze in on a correct rim. If you want some bling on your arm , what about a braced stock arm ?
Say a quick hello in here mate: http://www.streetfighters.com.au/for...To-The-Madness
Welcome aboard.
This is what I read on the subject you are chasing:
"Use a ZZR1100C wheel for the rear and a GPZ500S(D) for the front. A 180 tyre will fit using the original swingarm."
I've never done it but maybe someone here can confirm this.
What model you got?? I have a 92 a8 and the fork legs are 41mm (the one with 17" front wheel)exactly the same as a zz600 so you can with heavier springs just lide the complete front end in to the original gpz triples - this will give you a fully adjustable front end with all rebound,compression and pre load. A zzr600 rear wheel will also fit straight in ,I had my zzr6 and the gpz side by side and it looks like a direct bolt in job you will then be able to rum a 170mm rear tire. I have just bought 2 more gpz's that will make 2 and 1/2 in my garage.
There is a thread on gpzzone.co.uk about how to do this swap, apparently the c model arm os the best one to use
Thanks. I have got a 1984 900 and when I compare it to my sons zzr600 the 600 has a wider swingarm so I would have to machine on of the bushes down a bit . I like the look of the 900 that pizz did and it look like he used a zzr rear. I am just trying to get a bit of info to make sure I do it the best way. I will check out the uk site . thanks.
You have to pay to use that site you can't view anything on iit.
As far as I'm aware the gpz swing arm was the same from start to
Finish I'm getting an a4 85 mod delivered on Friday ill check it against
The a8 91mod when I get it for you.
But the zzr into the a8 is a sure bolt in I spent hrs looking at them side
By side.
I have had a look at a thread on gpzzone about this swap and they recon that the zzr1100c is the one to use, there is a 16 page thread including the dimensions etc. I have tried to copy the pic and will post it here.
I found this on the net on fitting a zx9 arm to a gpz as well., hope it helps
http://gpz750streetfighterbuild.wordpress.com/
Last edited by evad; 18-05-2013 at 05:22 PM.
Thanks for that evad. that is just what I was looking for. I may join the gpzzone site so that I can look at it. cheers.
Hey no worries, I was looking on my computer and found some really good info on gpz900s that were downloaded from gpz900.org before it disappeared when big andy got cancer There is a lot of info on gusseting the frame fitting front and rear ends etc, if you and damo pm me your email addresses I will send them on to you?
Last edited by evad; 19-05-2013 at 02:49 PM.
if you go with that i can help you out with making the spacers if needs be.
Thanks evad that stuff is great. I will have to study it a bit but if I go that way I will be in touch xa-mont. cheers.
No Problem, have you had a look at Ron's gpz called Hysteria build?
http://www.motor-forum.nl/forum/list_messages/210706/0/Sharp-Dressed-ZX10-Hysteria-1.html
if you translate it from dutch to english t give a fair idea of whats going on
Ron had a build thread over here too:Originally Posted by evad
No Problem, have you had a look at Ron's gpz called Hysteria build?
http://www.motor-forum.nl/forum/list_messages/210706/0/Sharp-Dressed-ZX10-Hysteria-1.html
if you translate it from dutch to english t give a fair idea of whats going on
http://www.streetfighters.com.au/for...ighlight=1000r
Yep but if you have a look at it the pics are dead
Iv got a ZZR1100 wheel.
"I call it a Camberwell carrot as I invented it in Camberwell and it looks alot like a carrot"
Yeah - that weird. The pics on the first 2 pages are there then the rest are dead (?)Yep but if you have a look at it the pics are dead
Any idea why Si? They're all ASF uploaded pics??
Rons gpz and z1r are 2 of my all time fav bikes......
Evad did you get my PM??
Hey Damo, got the first one with no email addy on it that I replied to but nothing after that.
Posting Permissions
Reply With Quote
