Umm help???

[Deano]

turbokat
ok i thourght up and drew that up in about 1 minute (not that you could tell)
so the rate is $50 for the first minute and $45 for every minute there after
plus fuel levy of 16% (that shit is getting expensive)
plus freight $50
multiply that by the exchange rate of 1.5 (queensland dollar to victorian dollar)
minus the streetfighter discount (add $300)
l'll just do the quick math on that
= $465.30 + gst per two hour job.
quite cheap when you think about the quality of my work

air brushing hey- i think i can help you out there (now where is that paint roller and the dulux wash and wear)

[TurboKat]

GOLD DEANO!
I'm back in my box now [B)]

[TurboKat]

GOLD DEANO!
I'm back in my box now [B)]

Heat the outer,WURTH have freon in a can that will freeze the centre.APPLY drift to outer.

Heat the outer,WURTH have freon in a can that will freeze the centre.APPLY drift to outer.

[Nate]

is that a big allen key in the middle if so u should be able to buy the in a 1/2 inch drive set of 6 for about $80 from the local tool guy and you could use a rattle gun

[Nate]

is that a big allen key in the middle if so u should be able to buy the in a 1/2 inch drive set of 6 for about $80 from the local tool guy and you could use a rattle gun

[Zed14]

i have a half inch drive allen key socket set oz but youre up there and im down here but you are welcome to come and get it or you could wait until mon night and i can bring it up for you cause i dont mind driving 800kms to help out a friend. thats if you need it of course but if you dont then dont worry about it.

[Zed14]

i have a half inch drive allen key socket set oz but youre up there and im down here but you are welcome to come and get it or you could wait until mon night and i can bring it up for you cause i dont mind driving 800kms to help out a friend. thats if you need it of course but if you dont then dont worry about it.

[Zed14]

or you could just get a kwaka like exben said. no special tools needed. thats because they think of the buyer unlike suzuki who only think about the dollars they can make on special tools. and then sell them to tools.

[Zed14]

or you could just get a kwaka like exben said. no special tools needed. thats because they think of the buyer unlike suzuki who only think about the dollars they can make on special tools. and then sell them to tools.

[ozkat]

actually no need at all to remove that thing. just undo the other end and slide the swingarm pivot shaft out. easy.

[ozkat]

actually no need at all to remove that thing. just undo the other end and slide the swingarm pivot shaft out. easy.

Yeah, except that I went to get a steering head adjuster tool for my GPZ9 yesterday, $120 for a simple tool, guess what I didn't buy (had to order it in anyway).

PS Any one got one sitting around they don't use anymore? Willing to make a copy of theirs?

Yeah, except that I went to get a steering head adjuster tool for my GPZ9 yesterday, $120 for a simple tool, guess what I didn't buy (had to order it in anyway).

PS Any one got one sitting around they don't use anymore? Willing to make a copy of theirs?

[ozkat]

ok got the new arm in but now waiting on bearing sleeves . should be back on the road soon. oh and thanks Deano ill get those dementions to you asap for the bearing sleeves.

[ozkat]

ok got the new arm in but now waiting on bearing sleeves . should be back on the road soon. oh and thanks Deano ill get those dementions to you asap for the bearing sleeves.

[ozkat]

ok to all the smarty pants out there, what is this? its under the battery tray i have NFI what it is or does. Neither does Gix11 cause i asked him.

[ozkat]

ok to all the smarty pants out there, what is this? its under the battery tray i have NFI what it is or does. Neither does Gix11 cause i asked him.

thats called a "circuit breaker".handy little fucker lets ya know when ya got a short in the wiring harness(but surely ya knew that)
mate,did ya tighten the swingarm clearance adjuster against the bearing seal cover before tightening the pivot shaft nut and clearance adjuster lock nut?[:0]