-
Umm help???
umm this might seem like a stupid question but.... how do i undo this? special tool or what?
-
Bloke with the stick
It's a fucker mate. Special tools are a rip off. I asked once and he Mal Maconnel was the only bloke who could get them. $300 or something stupid. The answer is a (blunt) cold chisel and a lump hammer mate.
-
Bloke with the stick
It's a fucker mate. Special tools are a rip off. I asked once and he Mal Maconnel was the only bloke who could get them. $300 or something stupid. The answer is a (blunt) cold chisel and a lump hammer mate.
-
requires special tools for the clearance adjuster and for the lock nut.let me know if ya need torque settings for reasembly.if ya get it off without fuckin it.
-
requires special tools for the clearance adjuster and for the lock nut.let me know if ya need torque settings for reasembly.if ya get it off without fuckin it.
-
Bloke with a smaller stick
Oz
could you make something like the above.
a raound peice of shafting to slide inside the hollow bolt.
weld a "tang" on the side to fit in the half moon cutout.
then weld a nut on the end of the shaft and undo with you favourite spanner.
the "tang" shouldn't bend to much as it should stay captive inside the 'outer' adjuster.
that will be $50 thanks
-
Bloke with a smaller stick
Oz
could you make something like the above.
a raound peice of shafting to slide inside the hollow bolt.
weld a "tang" on the side to fit in the half moon cutout.
then weld a nut on the end of the shaft and undo with you favourite spanner.
the "tang" shouldn't bend to much as it should stay captive inside the 'outer' adjuster.
that will be $50 thanks
-
nice art work Rolf Harris
-
nice art work Rolf Harris
-
Tyre destroying, mad bastard menace
Hey Deano, I'm thinking about getting some airbrushed murals done, what's your hourly rate?
-
Tyre destroying, mad bastard menace
Hey Deano, I'm thinking about getting some airbrushed murals done, what's your hourly rate?
-
Deano is booked solid for the next three years kitty,but its worth wating for such fine detail.
-
Deano is booked solid for the next three years kitty,but its worth wating for such fine detail.
-
Bloke with the stick
Mine came out with the cold chisel and it didn't fuck it. We tried loads of things before that but the old chisel did the job with one strike. It needed the impact to unlock it.
-
Bloke with the stick
Mine came out with the cold chisel and it didn't fuck it. We tried loads of things before that but the old chisel did the job with one strike. It needed the impact to unlock it.
-
Tyre destroying, mad bastard menace
Nah Oz it's to much stuffin around just sell it & buy a Kwaka...,go on you know you want to.
-
Tyre destroying, mad bastard menace
Nah Oz it's to much stuffin around just sell it & buy a Kwaka...,go on you know you want to.
-
i hear the KE175 makes a wicked fighter.[xx(]
-
i hear the KE175 makes a wicked fighter.[xx(]
-
Bloke with a smaller stick
turbokat
ok i thourght up and drew that up in about 1 minute (not that you could tell)
so the rate is $50 for the first minute and $45 for every minute there after
plus fuel levy of 16% (that shit is getting expensive)
plus freight $50
multiply that by the exchange rate of 1.5 (queensland dollar to victorian dollar)
minus the streetfighter discount (add $300)
l'll just do the quick math on that
= $465.30 + gst per two hour job.
quite cheap when you think about the quality of my work
air brushing hey- i think i can help you out there (now where is that paint roller and the dulux wash and wear)
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules