Dingo's GSXR hacker

[dingo]

figured i will start up my own progress and problems page.
it all started when this sad looking bike was offered to me.
i saw passed the paint, then i was put on this site, now i know what i got im happy i said yes. here's where it all started.http://www.streetfighters.com.au/forum/upload/17921841473047.jpg

[dingo]

http://www.streetfighters.com.au/forum/upload/17921841488291.jpg

stripped it down and just started anywhere

[dingo]

http://www.streetfighters.com.au/forum/upload/17921841469646.JPG

a week on the gernie and 6ltrs of paint stripper and the frame was sorta clean, thought hard about the colour.

[Large]

Bad moteur! You sit in the corner!!!1

[dingo]

http://www.streetfighters.com.au/forum/upload/17921841479116.JPG

had a small smoke signal when i was lifting the bike to put the forks on, my boy was putting bricks under the frame side by side for me, + terminal was off however i managed to press my fat gut against an earth wire onto the + terminal, murphy's law feels like 1/2 of it was for me.

[dingo]

quote:Originally posted by Large

Bad moteur! You sit in the corner!!!1

i was so tempted to paint it then , but what will i do another day when im bored:)

[dingo]

http://www.streetfighters.com.au/forum/upload/17921841492051.JPG

was just waiting for a rear disc for rego so i could see how it felt, was so tempted to just ride, but, if its gunna happen , it will happen to me, so i waited:D

[dingo]

just been enjoying this for a while , its been fun , had a few problems but i guess youve read about them, slowly sorting it out.
been colecting a few bits and decided to do a mock looksee.

[dingo]

http://www.streetfighters.com.au/forum/upload/17921841493455.JPG

the mock looksee didnt last to long, out with the grinder[}:)]

[dingo]

http://www.streetfighters.com.au/forum/upload/179218414100928.JPG

and so the madness bestowed unto ASF scared brain beguins[}:)]

[dingo]

http://www.streetfighters.com.au/forum/upload/17921841492874.JPG

'WOT THE FUK HAVE YOU DONE TO YOUR BIKE!'oh its ok dear, scottymac says its fixable;)

[dingo]

so thats where im up to as of today, thinking of making similar mounting brackets as opindowns but longer multi-hole brackets so i can change things round when i get bored.

[Gix11]

You've got the bug good and proper now mate. Looks loads better than when you got her. Keep us updated mate.

[dingo]

got some '91 USD's on the way to try out, low cut small zorst will be in order, then the rest as it comes

[porky gsxr]

i like it:D personaly i'd rake the arse end up[:p]but hey, its not my build[V]whats the seat unit? it will look the bollocks when done[^]

[dingo]

quote:Originally posted by porky gsxr

i like it:D personaly i'd rake the arse end up[:p]but hey, its not my build[V]whats the seat unit? it will look the bollocks when done[^]

gunna play with some bones later, '05 cbr 600 i think? will try follow the lines of the tank and the intake. may even shorten it another " or 2 ,not sure bout the seat yet.

[opindown]

hey dingo, I still have the plates drawn up in AutoCad. if you shoot me through your email then i can email them through to you. Do you have a copy of cad so you can alter them? If not i can shoot a copy to you express post if you are interested. Let me know.

[dingo]

cheers for the offer OD, just gunna throw some long plates on there and go from there, give me room for future thoughts.
not entiely sure how im gunna finish it off, got a few ideas but no doubt i will change my mind 1/2 way through and start again
so a multi-hole mount will be the go. not sure how that will look in the end but hey, its a street hack not a showie.:D

[Harry]

hey dingo....thats look'in ok mate,dont worry bout the hack not show pony dude we all do wat we can with wat we got mate..the forks look like there polish'in up well mate,get the tail sused and a squirt of paint on the motor and it will look hot :) all fighters are show bike's mate,reguardless of turbo's or nickle plateing....wat ever. it's in the building and yours is look'in fine,mine took years...chip at it mate she'll be a hottie and they don't make those motor's anymore,you have a classic :)

[dingo]

Cheers Harry, once i get it all together how i want it i will rip it appart again and give it a pretty up, i got a turbo sitting in the shed but i will learn to ride it first,lol plus it sounds way too expensive for me to do,would love to do it just for the experience though.

[dingo]

http://www.streetfighters.com.au/forum/upload/80610935778666.JPG

been havin a play with mounts, simple way to get it all lined up(slack way)cut and drilled the plates together then bolted em to the airbox/battery mount, just a queery guy's , you think 6mm plate will be enough to hang a subby off? me @86kg and wifey @68kg? , i got pillion rego otherwise i rekon it would be ok.

[dingo]

http://www.streetfighters.com.au/forum/upload/806109357105773.JPG

another mock together pic

[dingo]

please excuse my messy shed, its only a front carport, if i leave it a mess it just might confuse the little fukers wot to take first.
bit of luck they will slice their foot open too

[Harry]

no prob's with the shed carl i can only see your bike...ya got a turbo for that thing? you lucky fucker! put it on :):):) you going to have an animal.........i have faith in ya mate, 12 days to the rally ! sneak out i'll shout ya a really strong wild turky..........or 10:)
quote:Originally posted by dingo

please excuse my messy shed, its only a front carport, if i leave it a mess it just might confuse the little fukers wot to take first.
bit of luck they will slice their foot open too

[dingo]

[quote]Originally posted by Harry

12 days to the rally ! sneak out i'll shout ya a really strong wild turky..........or 10:)[quote]
use to love the turkey, now im obsessed with my own creation,its got the boot to knock over a cow with a glass and a 1/2 and you dont get the savage hangover in the morning.unfortunatly i wont make it to the AFR but i will be hangin on ASF to see how it turns out. will load up the back pack and have a ride down that way one day;)

[Harry]

no prob's mate.....rock on down anytime .
be prepared to get well pissed and talk bike's !bahaaaaaaaaaa
i'll take a shit load of pic's at the rally and put em up for ya ;)
im fully paid up and hang'in out for it......best 3 day's of the year[:p]

[dingo]

will be keen as to see em[:p] if i could find a sitter for the 4 kids it would be a great 1st holiday in over ten years for me and the missus.

[Harry]

in law's mate..........ten bloody years !; you need a ol'e day and so do i !...not that far mate just guz the big girl up and go[:p]
quote:Originally posted by dingo

will be keen as to see em[:p] if i could find a sitter for the 4 kids it would be a great 1st holiday in over ten years for me and the missus.

[dingo]

unfortunatly harry we are on our own in the sitting situation, we would spend more time worring bout our kids than having a good time:( , maybe next year i take the whole crew:D , fix my 4x4 first so we can all fit in a car wihout the worry of overload, know of any cheap VR V6 motors?

[pappas]

6mm plate sounds a bit thin for your subbie!

[dingo]

looks a bit thin once i stuck it on there too, will get some 10mm and see, better to be safe hey

[Harry]

no idea on the v6 mate...only thing i have to do with car's is round'in the bloody thing's up on my bike! ;)
quote:Originally posted by dingo

unfortunatly harry we are on our own in the sitting situation, we would spend more time worring bout our kids than having a good time:( , maybe next year i take the whole crew:D , fix my 4x4 first so we can all fit in a car wihout the worry of overload, know of any cheap VR V6 motors?

[dingo]

i let it run out of rego now, be easy enough to get a roadworthy now i got the mod plate, got a few leads to another donk but they want too much.

[Harry]

wont be to hard mate they crash the thing's every day just so there's spare's !

[dingo]

oh there is heaps around harry,but they all seem to forget its only the old classics worth money nowdays;)

[Harry]

cause they all want a NEW one mate.......wat a waste of money.
any progress on the bike mate?????
i wish my GSXR thiu would sell so i could get into my 96 bandit:(
depending on tax im going to go rank with it,got to flip the gixa first !

[dingo]

got a little more done, got the forks on ,got an old style enduro headlight for now, subby is almost finnished, slap on another can, and make a seat from a bread board and im on the road again, till i decide to paint it,lol. will throw up another pic in a day or 2. good luck on your sale, im gunna get the missus a 250 soon, shes keen to ride but i dont think the law will take too kindly to me towing a trailer with 4 kids in it :)

[Harry]

dont know about that mate,years ago there was a guy getting around toowoomba with an old 1300 kawasaki with a side car on it....him riding his mrs on the back and 3 kids in the side car! use to be a hell sight going down the road mate.
carl if your swingarm protector;the dealo that sit's between your chain and swingarm is flogged out shape a peice of teflon cutting board and slip it in,attach it with zip ty's..save your self around $140 bill's.....20thousand k's on mine,no wear!:)

[dingo]

use to make the same teflon/nylon breadboard bits for all chain wearing places on the dirtsquirts,lol, does save you heaps. sidecars,haha, i made one for the BMX to take the dog and my gear fishing, threw a few mates off it too.

[Harry]

if the maker's of cutting board only knew ! the crane i drive even has teflon chiv"s on it...mega strong !

[dingo]

haha, more uses than gaffa tape :)

[Harry]

http://www.streetfighters.com.au/forum/upload/77717471176025.jpg
mate check this dude out........he lived ![:0]

[dingo]

ouch!!!!, they probably fixed him with gaffa and a breadboard O_o

[Harry]

Hahaaaaaaaaaaaaaaaaaaa you unit,ya forgot zip ty's :)

[dingo]

wasnt sure they would have been able to find any, thought id bought em all, now im out again!

[dingo]

you got mail harry, check the last burnout :D

[Harry]

wild one on the pushie mate,the one in europe was out of control..was a wonder no one T-boned em ![:0]

[dingo]

this is my attempt sofar to make a seat, hasnt turned out the the shape i need it but i can always try again another day, still have to cut the lip off the back now cos it got shorter and shorter , might turn out ok , we see
http://www.streetfighters.com.au/forum/upload/44640103055549.JPG

[dingo]

here is a pic of the very technical process of moulding the bread/bait board

http://www.streetfighters.com.au/forum/upload/44640103062237.JPG
;)

[dingo]

slowly getting there , heaps to do , no time to do it :(

http://www.streetfighters.com.au/forum/upload/44640103092255.JPG

[Harry]

Thats come'in along fine carl,i like the blacksmithing work with the jackaroo mate [8D].
seat is a tad short but remember wen you have it upolstered it will bring it back another inch or two. it's fark'in piss'in down here....gunna be a kunt of a ride to casino but alais i have paid my due's and must attend ! even if i sleep in the mud and have nothing to do except drink heavly and look at people drinking heavly
Bahaaaaaaaaaaaaaa.:) fuck rain !:(

[dingo]

i saw the news with all that rain, was sopse to get on google and see how close it was to you guy's down there,fukn bummer i say, make for some interesting drifting vids hey;), maybe someone could take a trailer load of knobbies and you can all have mud fights[:0][:0][:0] all that time polishing. hope the rain fuks off for you all to enjoy the time you have there:D DONT GET YOUR CAMERA WET!!! you still have to take pics remember;)

[dingo]

yeah the seat was a bit longer , sorta like cutting the leg of an eneven chair, just got worse and worse, im gunna cut the lip off the back i think.

[Harry]

yeah mate its shit sorry sheet rain on the coast right now.......................FUCK FUCK FARRRRRRRRRRRRRRRK ! :(

[Surt]

quote:Originally posted by Harry

if the maker's of cutting board only knew ! the crane i drive even has teflon chiv"s on it...mega strong !


wtf is cuttin' board? a kitchen thing? [?][?][?]

[Surt]

quote:Originally posted by dingo

i saw the news with all that rain, was sopse to get on google and see how close it was to you guy's down there,fukn bummer i say, make for some interesting drifting vids hey;), maybe someone could take a trailer load of knobbies and you can all have mud fights[:0][:0][:0] all that time polishing. hope the rain fuks off for you all to enjoy the time you have there:D DONT GET YOUR CAMERA WET!!! you still have to take pics remember;)


yeeeaaaaaaaah, me too feelss sso sssorry 'bout rainss, ay-yesss, my preciousss [}:)] (fuckin' spittin' venom with envy [8D])

harry i count on ur pics 2! ;)

[Harry]

cut'in board hahaaaaaaaa,
it's a cutting board........timber,plastic,or teflon,for cutting food on surt so you dont have knife marks on your kitchen bench.
it's been re-shaped with heat for a seat base, it's cheap :)

[Surt]

hey dingo, so its still rainin' above mckay? [:0]
good luck to u with ur gixxer! and with ur kids, naturally, too...will never forget, when mine was under 1 yo... have learnt to have a nap in every free moment, coz there was no sleep at night :), no bikes buildin'[:0], nor ridin' [:0][:0][:0]

[dingo]

Hi Surt, no rain here, had 1 day of rain in the last 2 weeks, hasnt been to hot here either. been trying to get in an hour or so of fishing but way too much to do. i got 4 kids Surt 1 girl 3yo , and 3 boys 4,8 and 12 they sure are a handfull but i wouldnt change a thing. its been way too many years without a bike so now im gunna enjoy what i have.

[Harry]

there come's a time carl.......chip at ya scoot enjoy and never sell'oh and you better go and get a (viscetome?),nut's cut ! :)
TIME TO RALLY ! or as they say in the movie Highlander...THE GATHERING !;) how come i'v got to go and ride and party for 3 day's hahaha C YA

[dingo]

i worked out wot caused the kids and saw the doc harry, tell ya i was a bit nervous laying on the bed when he held that knife up,lol but no way were they gunna knock me out for it, 2 nurses and the doc, who knows wot the fuk they get up to,lol. have fun at AFR to you and everyone, dont forget the pics :D

[Surt]

quote:Originally posted by Harry

cut'in board hahaaaaaaaa,
it's a cutting board........timber,plastic,or teflon,for cutting food on surt so you dont have knife marks on your kitchen bench.
it's been re-shaped with heat for a seat base, it's cheap :)

so i got matey ;) just been surprised at the material: never seen one of teflon, or kevlar or aramid! :) just timber or plastic... u should send me one on appro!! [:p]

[dingo]

PM your way Surt:)

[Surt]

quote:Originally posted by dingo

PM your way Surt:)


ask harry he knows ways! :D

sittin' alone? me just back from job, its fuckin' blizzard again! [:0] not strong enough to blow me to oz, alas [V]

;)

[dingo]

kids in bed, missus and i doing puzzles while i email ASF good folk and making some fine degreaser to drink :)

[Surt]

meanin with kids... but at least one of them (12yo) is old enough to take care of others... i stayed alone at age of 6, also watched over my 2 ys younger broth :)

[Surt]

quote:Originally posted by dingo

kids in bed, missus and i doing puzzles while i email ASF good folk and making some fine degreaser to drink :)


degreaser? [:0] did harry pull u on kero?! [:0][:0][:0]

[dingo]

HAHA , yeah thats it, much too good to waste on polishing;)

[dingo]

i wouldnt trust my kids home alone Surt, they are ratbags :D dont think i would have much of a house to come home too

[Surt]

quote:Originally posted by dingo

i wouldnt trust my kids home alone Surt, they are ratbags :D dont think i would have much of a house to come home too

u should of built it not from straw mate! :) so why u didn't go? ur missus?? ;)

[Surt]

watch my new vid dingo!:

http://www.streetfighters.com.au/forum/topic.asp?TOPIC_ID=14181&whichpage=2

[^][^][^]

[dingo]

many reasons Surt, missus had an operation to got to which was cancelled , money, cant fit the family in the current car, money, work to be done , oh and did i mention money, haha , maybe next year when i got a new motor for the 4X4 , save some coin and we can all go down there, its only 1100 odd kilometres so its not like we are too far away.

[dingo]

hahaha, im not that old Surt , however i seem to remember watching that at some stage, HAHA, chuck norris, i laugh whenever i see people takin the piss out of him on the net. one thing that never fails to amuse me Surt is people getting swooped by birds and flicking a cigarette but in front of a cane toad, he laps it up with his tongue and spits it out so quick, fuk im laughing just thinkin bout it :D

[Surt]

quote:Originally posted by dingo

many reasons Surt, missus had an operation to got to which was cancelled , money, cant fit the family in the current car, money, work to be done , oh and did i mention money, haha , maybe next year when i got a new motor for the 4X4 , save some coin and we can all go down there, its only 1100 odd kilometres so its not like we are too far away.


well i thought u could ride alone, and, fark, i thought u live not far from harry... always forgettin' bout queensland size! looking at a map one could think its maybe 1000km long from south to north, but in fact, must be three times bigger...[?]

[Surt]

quote:Originally posted by dingo

hahaha, im not that old Surt , however i seem to remember watching that at some stage, HAHA, chuck norris, i laugh whenever i see people takin the piss out of him on the net. one thing that never fails to amuse me Surt is people getting swooped by birds and flicking a cigarette but in front of a cane toad, he laps it up with his tongue and spits it out so quick, fuk im laughing just thinkin bout it :D

i aint that old either carl, but all the oldie's shit they use to show us on the telly in 90s! so i of seen that kind of stuff, even reagan's films! :D:D:D

[dingo]

ive never been a TV person , always found something else to do, probably sit down to a movie once a week. even as a kid i couldnt sit down and watch it, had to go find some mischeif somewhere :D. as for riding alone, would do it , but my wife and i are quite tight, she would love to get out of this town for a week as much as i would....one day:)

[Surt]

quote:Originally posted by dingo

ive never been a TV person , always found something else to do, probably sit down to a movie once a week. even as a kid i couldnt sit down and watch it, had to go find some mischeif somewhere :D. as for riding alone, would do it , but my wife and i are quite tight, she would love to get out of this town for a week as much as i would....one day:)

me too, fuck tv and break the comp. i watch news twice a day and... a criminal news. i watched those films, 'coz before that they had never showed western movies in ussr ;) now i download movies and music via eMule, mostly...

[dingo]

i have to get my kids out more surt, the oldest one is a keen hockey player but they spend way too much time on their fukn NINTENDO's , even when we go camping they want to bring em, i tell em put em in the drawer and grab your fishing rod, the game stays home! , few hours of catching fish and they forget all about the games.

[Surt]

quote:Originally posted by dingo

i have to get my kids out more surt, the oldest one is a keen hockey player but they spend way too much time on their fukn NINTENDO's , even when we go camping they want to bring em, i tell em put em in the drawer and grab your fishing rod, the game stays home! , few hours of catching fish and they forget all about the games.


wat u aussies call hockey? a field hockey? we play the ice hockey... [8D]

[dingo]

yeah same thing but on grass field with a ball, crazy game, kid got rushed off to the hospital the other day, fractured skull, no helmets, just shin pads, the goalie wears all the gear though.

[dingo]

http://www.streetfighters.com.au/forum/upload/831242056102130.JPG

not much of an update, i still got so much to do but finding the time is the key, still, big improvement to where i started from[8D]

[BANDITROD]

lookin good mate it has definitly come a long way

[dingo]

sitting on the carpet inside in the air-con rewiring the loom, too bloody hot outside in the carport, still deciding if i do a low mount exhaust or angle it the same as the tail, i got some old 62mm pipe off the 4X4 to run to the can, but i think that may be a bit loud, performance is not an issue at the mo.

[Fight_fan]

Definatly come along way mate! She's really takin shape!

[Surt]

quote:Originally posted by dingo

sitting on the carpet inside in the air-con rewiring the loom, too bloody hot outside in the carport, still deciding if i do a low mount exhaust or angle it the same as the tail, i got some old 62mm pipe off the 4X4 to run to the can, but i think that may be a bit loud, performance is not an issue at the mo.

wat carl, r u gonna fetch the exhaust from ur toyota? [:0][:0][:0]
............................
...............................
..................................
sick, man!!! but then, a snorkel too, so u can cross ur pioneer river wherever u wanna, fisho! ;)

[:p]

[Surt]

and u should definately relocate ur bike buildin' into ur living room, like myself, that could be fuckin' hot or freezin' cold in the garage, but inside: conditions, the frige, the comp, the kitchen and the bathroom; how rich a man should be to afford those in one's garage!!! [8D]

[Surt]

a noice bike is ccomin' along mate, keep the colour as is ;)... already installed the big cams Carl?

[latheboy]

Looks heaps and plenty good, make sure you get a tune done when you change the pipe....
I reckon you should go for the under slung can, i dig them and it keeps the weight down low too...

[dingo]

quote:Originally posted by Surt


quote:Originally posted by dingo

sitting on the carpet inside in the air-con rewiring the loom, too bloody hot outside in the carport, still deciding if i do a low mount exhaust or angle it the same as the tail, i got some old 62mm pipe off the 4X4 to run to the can, but i think that may be a bit loud, performance is not an issue at the mo.

wat carl, r u gonna fetch the exhaust from ur toyota? [:0][:0][:0]
............................
...............................
..................................
sick, man!!! but then, a snorkel too, so u can cross ur pioneer river wherever u wanna, fisho! ;)

[:p]

the exhaust is the old one from the turbo system befor i put the V6 in it,aprarantly they have given me 3 months to pay the rego on the 4x4 so i may be able to keep that rego'd yet.
without the 4x4 on the road the GSXR may just get 1 or 2 trips across a dry salt pan to my other fishing spot ;)
the cams arent actually oversize or anything, they are out of a similar breed of bike ,spose to be the same with a little more lift,let you know how that one goes, they should be here today or early next week:)
oh how life would be so much better if i could bring it inside[:p]

[dingo]

quote:Originally posted by latheboy

Looks heaps and plenty good, make sure you get a tune done when you change the pipe....
I reckon you should go for the under slung can, i dig them and it keeps the weight down low too...

i rekon under would definatly look better too lathe, will make up both options and see:)

[Surt]

quote:Originally posted by dingo


quote:Originally posted by Surt


quote:Originally posted by dingo

sitting on the carpet inside in the air-con rewiring the loom, too bloody hot outside in the carport, still deciding if i do a low mount exhaust or angle it the same as the tail, i got some old 62mm pipe off the 4X4 to run to the can, but i think that may be a bit loud, performance is not an issue at the mo.

wat carl, r u gonna fetch the exhaust from ur toyota? [:0][:0][:0]
............................
...............................
..................................
sick, man!!! but then, a snorkel too, so u can cross ur pioneer river wherever u wanna, fisho! ;)

[:p]

the exhaust is the old one from the turbo system befor i put the V6 in it,aprarantly they have given me 3 months to pay the rego on the 4x4 so i may be able to keep that rego'd yet.
without the 4x4 on the road the GSXR may just get 1 or 2 trips across a dry salt pan to my other fishing spot ;)
the cams arent actually oversize or anything, they are out of a similar breed of bike ,spose to be the same with a little more lift,let you know how that one goes, they should be here today or early next week:)
oh how life would be so much better if i could bring it inside[:p]

oh no, i didnt mean oversized, otherwise they wouldnt get in the smaller engine! :D i meant shafts with bigger cams, not bigger shafts, matey!

[dingo]

Surt- HEHE, they should make one size fits all 4cyl bikes, just different lift and duration, make life a lot easier for all :)
finish off the wiring tomorro, bit easier than playing with ECU's;), should be having my first ride on my new bike next week[:p]

[Surt]

quote:Originally posted by dingo

Surt- HEHE, they should make one size fits all 4cyl bikes, just different lift and duration, make life a lot easier for all :)
finish off the wiring tomorro, bit easier than playing with ECU's;), should be having my first ride on my new bike next week[:p]

bloody bas'rds, ther r makin' money from every little shit... say cams, fuck, take any connector, so many different types, kunt find a proper one for fast idle for 6 months even on ebey! [:0][:0][:0]
[xx(]
good luck with ur weelz mate! :)

[Harry]

lookin good carl, you've been busy mate!
nearly ready for a trip south ;)...sold my k3 thou last friday [:p]
nearly time to attack my 96 bandit ! be good mate [^]

[dingo]

Hi Harry, hows things?, would love a trip away;), got a few wire probs atm, stuck it up in the 'advise' section, was all keen to have the first ride on it too. get wot you wanted for the K3?

[Harry]

well mate i got my $7.5k for it but it was worth more,lot'a bike for the money carl but it's a sign of the time's.at least i can get something happening with my bandit mate...trying to track down an old retired machanic thats done most of my work for 31years..see if he'll do a rebuild for me,think he's in hiding but i'll track him down ! :)

[dingo]

good luck with the build , im sure you will have no worries putting that coin to good use. you gunna go the whole hog with it or just a modest build?

[Harry]

gunna look into GSXR thou front and ass end mate,somewhere around a K5 model.......need to be able to take my kid's for a spin on it so im think'in a buell sub frame to retain a pillion seat carl or my young fella will knife me in my sleep [xx(] haha. frist thing is the motor mate,rebuild,respray & some braided lines to re-place the hose's on it...oil cooler ect. going to take some time but i'll chip away at it ;)

[dingo]

sounds good harry[:p], was thinking of getting another project to do properly but i just havnt the space. thought hard about that slabbie but the coin is not there, im gunna gather the rest of my bits n bobs n paint before i start to freshen this up otherwise i spend weeks waiting for the parts i need to proceed, would rather spend weeks building and painting with all i need at hand, might even look into a small kit shed, this carport is the fukn pitts i tell ya:(

[Harry]

im hear'in ya mate,no shed my self [V], was looking at a two bay with work shop built in but im not game to add ten grand to the loan right now.near got the joint paid off and work is slim pickin's right now & iv promised my wife a kitchen:( the bandit will live again mate shed of not :)