Got some new toys at work.. Building a TIG trolley too... and other Stuff. [Archive]

Gitzy

15-07-2014, 07:03 PM

Long story short needed to cut a few thousand slotted holes that my press couldn't do, so said to boss whose a top dude "can't cut these with oxy that'll suck mass balls" a few days later got this....

fun little gadget after using the oxy for years.

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140715_115241_zps3fe19aa1.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140715_115241_zps3fe19aa1.jpg.html)

Also I'm in my 3rd year now and my TIG skills weren't up to par I don't think with a total of a few hours experience and not wanting to fudge my tafe expectations I asked for a HF TIG Welder.
and voila.. on a side note we have ZERO need for a TIG in my workshop but we got one anyway so I'm chuffed with that, let the foreigners begin..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140715_140148_zpse530623e.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140715_140148_zpse530623e.jpg.html)

Had a guy come out from allweld today and give me a run down on some basics before leaving me to make my own mistakes..

The only bit of stainless I had laying about was some 100x100x10 Equal angle.. thought hey it'll do for a butt and some fillets, this is my first attempt ever at stainless I just set it on some settings the manual suggested, turned out to be a very flat butt and a very concave fillet, sooo neeeed a lot of practice..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140715_153143_zpsdedcb962.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140715_153143_zpsdedcb962.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140715_153212_zps29e20ce2.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140715_153212_zps29e20ce2.jpg.html)

Then for the Aluminium, same deal manual suggested settings. It was only an outside corner on 50x3 flat, I honestly thought it was going to be a lot harder but I found it the easier of the bunch compared to SS or MS.

Ignore the burred bottom edge I just cut it off with the grinder to run some beads, I only had a few pieces of alloy..

So anyway new toys new skills to work on much fun..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140715_153054_zpsedff9fac.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140715_153054_zpsedff9fac.jpg.html)

Snaffler

15-07-2014, 07:49 PM

hmmm i gots me some things that need tig welding :)

good job dude and will make life alot more easy now..

Dano919

15-07-2014, 09:37 PM

Custom stainless exhausts anyone?!

Big Dan

16-07-2014, 07:23 PM

Who was it from Allweld Todd? Ive been with them just over 2 years now:cool: The Razor range are a good unit I know the boys at work love them

latheboy

16-07-2014, 08:16 PM

De bur everything, that Shitty ground edge wouldn't fly in my factory...

Nice welds for you first runs... Practice as much as you can..

Gitzy

19-07-2014, 08:14 PM

Mark, I gots me heaps of stuff to weld, not sure If I'm any good at it either lol.

Dan that would be the bombdiggity if I could do a custom zorst.

Big Dan, it was ummm Paul I think, good dude.

Will do Ivan, practice practice practice..

Gitzy

07-08-2014, 09:15 PM

Started making my trolley today, tig on top, plasma on bottom..

500 x 900 shelves made from 3mm plate and 25x25 RHS..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140807_144052_zps94d267c4.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140807_144052_zps94d267c4.jpg.html)

Gitzy

07-08-2014, 09:16 PM

then cut up some 40x40 for the frame..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140807_144119_zps6f13fd0d.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140807_144119_zps6f13fd0d.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140807_144321_zps23bdeb1d.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140807_144321_zps23bdeb1d.jpg.html)

Gitzy

07-08-2014, 09:16 PM

Welded it all up..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140807_155010_zps5d2a5b42.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140807_155010_zps5d2a5b42.jpg.html)

Gitzy

07-08-2014, 09:18 PM

I was going to bolt the wheels but ended up spot welding them to some 90x10 plate..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140807_160254_zps1a6f151b.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140807_160254_zps1a6f151b.jpg.html)

Mounted the wheels and chocked up the rear to sort out the back wheels..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140807_162728_zps23538eaa.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140807_162728_zps23538eaa.jpg.html)

ozzy1100

07-08-2014, 09:18 PM

fucking spolit

Gitzy

07-08-2014, 09:20 PM

The overall trolley looks rather large compared to the wheels but they are 200 x 50ish they'll do the trick nicely.. used some 1/2 inch tube and thread bar to suit the axle diameter req for the wheel..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140807_162735_zpsf16a053a.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140807_162735_zpsf16a053a.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140807_163520_zps4dc59628.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140807_163520_zps4dc59628.jpg.html)

Gitzy

07-08-2014, 09:21 PM

welded the tube under the back rail..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140807_165121_zps1840e581.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140807_165121_zps1840e581.jpg.html)

Gitzy

07-08-2014, 09:22 PM

Progress so far..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140807_165303_zps4874fb0f.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140807_165303_zps4874fb0f.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140807_165526_zpsa4cb1406.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140807_165526_zpsa4cb1406.jpg.html)

ozzy1100

07-08-2014, 09:25 PM

gas bottle ?

Gitzy

07-08-2014, 09:26 PM

Things to still do..

*fit the back end to support the G size bottle of argon.
*fit hooks for cables etc.
*mount my allooominum :p drawer I made from earlier.
*sort a mounting out for the 40mm PVC I'm storing my filler rods in.

Gitzy

07-08-2014, 09:30 PM

fucking spolit LOL just motivated to make shit at the moment, for which I blame you Lynton..

I even got rid of my half cut 44's with various stock cut up and made a spiffy little shelf..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140807_130631_zps0c5f0463.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140807_130631_zps0c5f0463.jpg.html)

ozzy1100

07-08-2014, 09:30 PM

then i would move the wheels to behind where the bottle will be or there will be to much weight over the axis imo

ozzy1100

07-08-2014, 09:31 PM

it sounds silly cause im such a messy worker but work flow just makes things so much easier

Gitzy

07-08-2014, 09:40 PM

then i would move the wheels to behind where the bottle will be or there will be to much weight over the axis imo

I was thinking that, If needed I will for sure I'll only need to unbolt the wheels and weld another tube on behind the wheels i really only put them where they are for now because I prob won't get to it again for a little while..

ozzy1100

07-08-2014, 09:50 PM

it wont be if ... just when, trust me u will move them lol

Gitzy

11-08-2014, 07:53 PM

Soooo Lynton was right... shhh don't tell him... got some bigger wheels 264 x 80 heavier rated too so should do the job with ease..

started to put the gas platform on today, wheels are just mocked up.

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140811_164453_zpsbb780e59.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140811_164453_zpsbb780e59.jpg.html)

come up with an idea for filler rod storage, pinched off another trolley I found pictures of on google.

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140811_164511_zps7fcd8b93.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140811_164511_zps7fcd8b93.jpg.html)

3 off 40 x 1000 pvc tubes for each side, one side for 1.6mm the other for 2.4mm SS, Alloy and MS respectively .

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140811_164710_zps96f52b3f.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140811_164710_zps96f52b3f.jpg.html)

ozzy1100

11-08-2014, 08:03 PM

when will you people learn i am always right.... oh and you need more then three wire holders, i did three and now i have to do at least 2 more :-(
nice mig torch stand to btw

Gitzy

11-08-2014, 08:29 PM

Read man read... lol.

3 off 40 x 1000 pvc tubes for each side, one side for 1.6mm the other for 2.4mm SS, Alloy and MS respectively .

I was sick of the torch dropping on the ground, and I haven't lashed out on one of them magnetty ones yet so this will do the trick :D

ozzy1100

11-08-2014, 08:34 PM

carry on lol
i made one for the tig out of holden 202 tappet cover t bolts if it works it works

Gitzy

12-08-2014, 09:24 PM

Finished the other pvc holders and welded it up..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140812_073144_zpsb256eb4c.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140812_073144_zpsb256eb4c.jpg.html)

Drilled some holes to suit the new axle..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140812_100555_zps818cd0fb.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140812_100555_zps818cd0fb.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140812_100925_zps830ed94e.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140812_100925_zps830ed94e.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140812_101619_zpsfbfac088.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140812_101619_zpsfbfac088.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140812_102026_zpse1987bb4.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140812_102026_zpse1987bb4.jpg.html)

Gitzy

12-08-2014, 09:25 PM

Now its a roller... (again)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140812_102540_zps0572e387.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140812_102540_zps0572e387.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140812_102554_zpsbb49adc6.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140812_102554_zpsbb49adc6.jpg.html)

Gitzy

12-08-2014, 09:27 PM

Cut some plate to suit the diameter of the gas bottle..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140812_104101_zps65d82953.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140812_104101_zps65d82953.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140812_104228_zpsed9a78a2.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140812_104228_zpsed9a78a2.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140812_105845_zps877c0b72.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140812_105845_zps877c0b72.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140812_115559_zps5b452b76.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140812_115559_zps5b452b76.jpg.html)

Gitzy

12-08-2014, 09:32 PM

Put some rolled round bar on for cable holders.. I cut up some plate today to make a 500 x 600 x 200 deep drawer that I'll make soon.

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140812_124310_zps39528b67.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140812_124310_zps39528b67.jpg.html)

ozzy1100

12-08-2014, 11:36 PM

that will do pig... that will do

xa-mont

13-08-2014, 11:54 AM

Very nice Gitzenburg

Gix11

13-08-2014, 02:10 PM

Shit yea; That's cool.

wackyrider

13-08-2014, 03:07 PM

nice one Gitzy

Nudie

13-08-2014, 07:10 PM

Very impressive and I want one too! (I haven't got a clue what any of it is for, but everyone else likes it)

Gitzy

13-08-2014, 08:15 PM

Lol cheers Lads..

started making the drawer today, should be great outside corner tig practice... I tried DC Pulse for the first time on my first edge, (only had time for one weld) Peak 150A background 35A and 150HZ (I kinda just guessed), it was bloody quick I'll tell you that much it felt like a mig for a little bit there.. I have plenty more to practice on fiddling with the settings..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140813_142602_zpsf9163edc.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140813_142602_zpsf9163edc.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140813_145808_zpsfd53a61e.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140813_145808_zpsfd53a61e.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140813_151011_zpsaeb17871.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140813_151011_zpsaeb17871.jpg.html)

ozzy1100

13-08-2014, 08:51 PM

33% rule

Gitzy

13-08-2014, 09:34 PM

Ahhh huh???

ozzy1100

13-08-2014, 10:13 PM

set pules by 33%... back ground 33% of peak and 33% if you play with time
try it so say 100 amp peak 33 amp background but with most trings it is personal

Gitzy

14-08-2014, 01:29 PM

Ahhhh understand I do.. :-)

Gitzy

14-08-2014, 09:13 PM

Finished my drawer today..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140814_084739_zps01afa7a3.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140814_084739_zps01afa7a3.jpg.html)

and fitted to the trolley..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140814_085053_zpsccb158d8.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140814_085053_zpsccb158d8.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140814_085150_zpsd826ad25.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140814_085150_zpsd826ad25.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140814_085322_zps41d87863.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140814_085322_zps41d87863.jpg.html)

ozzy1100

14-08-2014, 10:31 PM

nice

Big Dan

15-08-2014, 07:33 PM

Looks good Todd you need some Allweld stickers on it mate ill get you some:p

Snaffler

18-08-2014, 12:39 AM

now thats a spiffy trolley you have made todd but i didnt see any drink holders?

Gitzy

18-08-2014, 06:02 AM

Lol cheers Dan that would be super.. they aren't the stickiest stickers I've seen though.

There's plenty of bench space around said TIG machined Mark lol.

Snaffler

18-08-2014, 10:17 AM

oh i thought that space was for putting your head down and sleeping on the job lol..

nar i only jokes dude, it really is a neat trolly you made champ..

Barra58

24-01-2015, 04:40 PM

Very sexy, me jealous, is a huge credit to you. Yeah I know threads a bit old now, but I'm new here so doesn't matter. :p

Gitzy

24-01-2015, 08:32 PM

Cheers Mate, painted it since then..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140902_122739_zps9yqxgzjh.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140902_122739_zps9yqxgzjh.jpg.html)

Built this for a Mate and used the spare hammertone grey on the trolley..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140826_065157_zpskah5lftj.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140826_065157_zpskah5lftj.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20140829_170446_zpsft1ra1bs.jpeg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20140829_170446_zpsft1ra1bs.jpeg.html)

Gitzy

24-01-2015, 08:34 PM

Another little project I've done lately is spruce up my old mans 7x4.. he's had it forever and wanted to make it more camp worthy, so made the sides 300 higher.

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/FOT4BB7_zps07skmgwq.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/FOT4BB7_zps07skmgwq.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/Welding1_zps02zpugf2.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/Welding1_zps02zpugf2.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20141015_170402_zpszrpckov3.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20141015_170402_zpszrpckov3.jpg.html)

Put a lid on her with some gas struts..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20141018_110751_zpssesf8lvm.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20141018_110751_zpssesf8lvm.jpg.html)

Gitzy

24-01-2015, 08:35 PM

Chopped off the stumpy draw bar and extended that bad boy..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/Created%20with%20Nokia%20Smart%20Cam_zpsuuhusbri.j pg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/Created%20with%20Nokia%20Smart%20Cam_zpsuuhusbri.j pg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20150103_130752_zpsltg1xymd.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20150103_130752_zpsltg1xymd.jpg.html)

Gitzy

24-01-2015, 08:39 PM

Painted her up, he put on a staino gullwing toolbox for his fridges etc and a stone guard and some chunky rims and tyres, came up a treat, I've since compiled some parts so I can make one for myself ground up..

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20150120_155625_zpsnqtdyngn.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20150120_155625_zpsnqtdyngn.jpg.html)

Barra58

24-01-2015, 09:24 PM

Hey Mate, that's farkin awesome, I take my hat off to you, that is some magic engineering, keep the pics coming. :)

xa-mont

25-01-2015, 10:13 AM

doing some good work there gitzenburg

BANDITROD

26-01-2015, 11:01 PM

Now your talking my language glitzy very nice

wackyrider

28-01-2015, 09:00 PM

Nice on Gitzy

Slim

17-01-2016, 12:57 AM

Nice work mate

Gitzy

17-01-2016, 07:09 PM

Cheers Mate made another camper in the christmas holidays, took 5 days total to get it this far.. http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/001_zpsts0quh1b.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/001_zpsts0quh1b.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/006_zpsck3o1xu3.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/006_zpsck3o1xu3.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/015_zpstc2jnepe.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/015_zpstc2jnepe.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/020_zpszrgalsfy.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/020_zpszrgalsfy.jpg.html)

Gitzy

17-01-2016, 07:10 PM

http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/024_zpsbsmqdqmi.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/024_zpsbsmqdqmi.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/029_zpspt1t5fno.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/029_zpspt1t5fno.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/032_zps7xihznar.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/032_zps7xihznar.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/035_zpsrjejte14.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/035_zpsrjejte14.jpg.html)

Gitzy

17-01-2016, 07:11 PM

http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/039_zpst7wjeyne.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/039_zpst7wjeyne.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/040_zpshxa6uit0.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/040_zpshxa6uit0.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/041_zpsmuhbgqwb.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/041_zpsmuhbgqwb.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/042_zps04sdgcvw.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/042_zps04sdgcvw.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/043_zpsb0kqwicp.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/043_zpsb0kqwicp.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/045_zpspiamf2ud.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/045_zpspiamf2ud.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/047_zpsnknmbjfn.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/047_zpsnknmbjfn.jpg.html)

Gitzy

17-01-2016, 07:12 PM

http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/052_zpszrckvqxq.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/052_zpszrckvqxq.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/054_zpsgvpzfgu8.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/054_zpsgvpzfgu8.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/055_zpsfshhus7j.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/055_zpsfshhus7j.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/057_zpsz4vxpm3e.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/057_zpsz4vxpm3e.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/059_zpsf0h4kir6.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/059_zpsf0h4kir6.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/060_zpsqczmk7mb.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/060_zpsqczmk7mb.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/064_zpsakjabnbg.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/064_zpsakjabnbg.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/069_zpsqzerbrr2.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/069_zpsqzerbrr2.jpg.html)

Gitzy

17-01-2016, 07:13 PM

http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/070_zpsigswqxpg.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/070_zpsigswqxpg.jpg.html) http://i1359.photobucket.com/albums/q786/gitzyfighter/Trailers/My%20Trailer/071_zpspp3f5fut.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Trailers/My%20Trailer/071_zpspp3f5fut.jpg.html)

Slim

17-01-2016, 07:15 PM

Thats come along well for 5 days mate, I'd still be moving stuff around to get to my dropsaw by day 5 haha.

I like the small touches like the grease nipples in the hinges. Those are the little things that make the difference after you've had it for a few years

Gitzy

17-01-2016, 07:17 PM

Just kept it simple and clean. In the last week I've had a thousand other ideas and I'll prob make another one next year wouldn't mind one with offroad suspension that I can sleep in bit like this without the massive pricetag.

http://terrafirmaadventures.com/wp-content/uploads/2013/04/conqueror-commander-01.jpg

Gitzy

17-01-2016, 07:20 PM

Thats come along well for 5 days mate, I'd still be moving stuff around to get to my dropsaw by day 5 haha. Lol I was motivated, I may or may not have cut all of the steel required leading up to the holidays whilst being on the clock ;-)

Slim

17-01-2016, 07:24 PM

Haha, I knew it!! lol

Im looking to build an offroad camper with independent coil suspension as well. Its one of those, 'one day I'll get around to it' jobs. Yours have given me a couple of ideas though. Great job!

latheboy

18-01-2016, 01:37 PM

Lol I was motivated, I may or may not have cut all of the steel required leading up to the holidays whilst being on the clock ;-)

Being Sponsored by work is awesome, I get heaps on things sponsored for my projects :)

ozzy1100

18-01-2016, 01:54 PM

Being Sponsored by work is awesome, I get heaps on things sponsored for my projects :)

and your work is all kinds of awesome already......

latheboy

18-01-2016, 02:22 PM

Only sometimes, I wish I could post pictures from work but secret squirrel and IP stuff so NOPE no pictures ...

Something I did late last year that I can show you.
https://www.facebook.com/quickbitzmichael.kalaitzakis/videos/1057846987566937/

2000hp Hub Dyno.
This car lifts the front wheels on a trans brake start :)
Sitting in the car on the trans brake waiting for the boost to get to 45PSI and then launch was fun.
And no I didn't drive and yes I had my feet well away for the tunnel haha

latheboy

18-01-2016, 02:23 PM

double post

ozzy1100

18-01-2016, 04:26 PM

Gitzy

06-04-2016, 08:56 PM

Seen as though I've been doing fuckall on the bike front, I knocked up this flat pack fire pit today. Came up a treat.

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20160406_090848_zpsg0vgthyh.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20160406_090848_zpsg0vgthyh.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20160406_090759_zpskbggd7fy.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20160406_090759_zpskbggd7fy.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20160406_104310_zps06uzp4zz.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20160406_104310_zps06uzp4zz.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20160406_133557_zpsxubxzjgp.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20160406_133557_zpsxubxzjgp.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20160406_133614_zpsh9nbqsdq.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20160406_133614_zpsh9nbqsdq.jpg.html)

http://i1359.photobucket.com/albums/q786/gitzyfighter/Various/Welding/20160406_133622_zpswmgrsywg.jpg (http://s1359.photobucket.com/user/gitzyfighter/media/Various/Welding/20160406_133622_zpswmgrsywg.jpg.html)