Chadams motoplast frame and now a z1000

[chadams]

Well guys I bought it.... hehe I want to have it ready for next years fools run..

I've now have a donar bike a z1000 1981 model.

http://www.streetfighters.com.au/forum/upload/6464062453145.JPG

http://www.streetfighters.com.au/forum/upload/6464062456312.JPG

http://www.streetfighters.com.au/forum/upload/6464062456871.JPG

http://www.streetfighters.com.au/forum/upload/6464062454565.JPG

http://www.streetfighters.com.au/forum/upload/26037302056541.JPG

[Large]

what's it designed for?

how old?

has it been registered in nsw?

[fimpBIKES]

cool, now send it off to the powdercoaters :D

looks like you'll be in the shed for the next few months Chad,may the force be with you.

[TurboKat]

[:p][:p][:p][:p] FUCKIN HORN [:p][:p][:p][:p]
Nice work Chad, you've got the basis for a kick arse bike there mate.
Now get to work. :D

[Tony Nitrous]

Nice one,
Well done,
Dont know much about frames but it looks good,
Lots of triangular bracing is always good.

What lump WAS in it ?
What lumps GOING in it ?

One off frame.... The "Next Level" ;) [8D]

Tony.J.

[devo]

Tell us the price son.;)

[speeddemon]

Im sure chad will tell more, but its for old klacker engines (GPZ900 and others). The frame is so strong - little bit heavier than a new gen spondon but real well made and braced to shithouse.

Lets say that chad being my sith apprentice i hence comanded him to make it a angry monster of a beast - or should i say APE hint hint...

Ill let him tell you the price

[chadams]

I'll be putting a gpz1100 84 preferred, same as my old one... I should be able to pick one up in good nick with rego for about $2000.....
Project so far, forks, brakes and triples all zx6 2005 ($700) and wait for it.....

The frame kit for $1500..... hahaha... I luv it.....

[chadams]

Gix, where's the pixs gone to?? :-)

[chadams]

its alright now... I'll was getting a local host error... odd... :-)

[gibbo]

$1500?, well done Chadams! Make sure you give us plenty of photos of the build.

[chadams]

I just measured up the swing arm and compared it to my z750 (2005) and the inside distance at the end of the swingarm is almost the same, the z750 is about 1mm wider... This means I will be able to run any late model kawasaki rear wheel, sprocket carrier and braking... The motoplast swing arm is also a little shorter then the z750... I have bike and car rego over the next two months.. but the build will get serious in october, maybe ready for summer...

[fimpBIKES]

a chunky late model swinger (braced of corse)
would look sweet with that frame


$1500 is a bargain and a half including that tank!!!

[NakedTurboBusa]

yep that frame is sweet.... and a fucking bargin!

[Gix11]

Nice find Chadams. That's a tasty looking Frame. Those tubed farmes can look either right or very wrong, and you have yourself a RIGHT one there!

[speeddemon]

apparently the italians were good at something long ago! for once.

By the way the dude chad bought it off span off a long list of well known racers in Aus who actaully owned this frame at one time or another. fucked if i know who they are - i was only 10 then i suppose.

[fimpBIKES]

i know straight from the horses mouth that the ducati frames are made in the UK
just like that exy bitch fergie [:P]

[chadams]

Below is a mock up with the front end... all I need now is a motor, some wheels, some paint, a seat... a couple of grand and it's all done.

:):):):)[8D]

http://www.streetfighters.com.au/forum/upload/50594272930649.JPG

and an Exben,
the frame is bent mate

[fimpBIKES]

i think your eyes are bent?!?!

its also rusting from inside out,a bit like your Mrs fImP!?!?

[Gix11]

The forks aren't square on in that shot Davo, look at the axle........

[devo]

Ok then the axles bent :D

look harder, the frame is bent. possibly by a mandrel bender.

[Gix11]

Ah yes. The obvious ones always get me.......

[Matt]

Looks great mate. looks like you will be quite busy over the next couple of months.......

[damo1]

need paint and body work ?
call Damo
if you need some work done Chads let me know ill look after you.

[chadams]

cheers mate... I'll be needing some work in the near future..