-
-
ASF Premium Full Member
hiya
im looking to do a similar thing on the tiller, but am making up a whole new upper yoke outta 20mm AL
mmm, bar end mirrors..
damn i cant find anywhere. i was sure i knew a place
wait up i shall search a bit
-
ASF Premium Full Member
hiya
im looking to do a similar thing on the tiller, but am making up a whole new upper yoke outta 20mm AL
mmm, bar end mirrors..
damn i cant find anywhere. i was sure i knew a place
wait up i shall search a bit
-
ASF Premium Full Member
-
ASF Premium Full Member
-
Thanks Fimp, good work.
I actually picked up a set of MCS bar-end mirrors, which only require a minor adaptor and 'normal/micro' indicators mount straight up to them. I've got micro 'arrow' indicators on there already.
The bolts on the mirror mounts and the indicator mounts are the same size/pitch etc, I had the original mirror bolt drilled out, head cut off it, and a threaded collet made up which joins the two bolts (after shortening the indicator bolt) and voila the two mate together like a bought one.
Still got to figure out the headlight bit though.
-
Thanks Fimp, good work.
I actually picked up a set of MCS bar-end mirrors, which only require a minor adaptor and 'normal/micro' indicators mount straight up to them. I've got micro 'arrow' indicators on there already.
The bolts on the mirror mounts and the indicator mounts are the same size/pitch etc, I had the original mirror bolt drilled out, head cut off it, and a threaded collet made up which joins the two bolts (after shortening the indicator bolt) and voila the two mate together like a bought one.
Still got to figure out the headlight bit though.
-
ASF Premium Full Member
sounds nice an tidy,
got pics??
-
ASF Premium Full Member
sounds nice an tidy,
got pics??
-
Once my daughter brings the bloody camera back.
-
Once my daughter brings the bloody camera back.
-
OK, here the Geepz has gone from Amanda Vanstone to Twiggy
And here we're starting to add some "tit's and ass" to it.[8D]
The headlight/dash/bracket are to be replaced this week, then it's back on road for some fun.
Anyone know where to get jack-up kits from locally?
-
OK, here the Geepz has gone from Amanda Vanstone to Twiggy
And here we're starting to add some "tit's and ass" to it.[8D]
The headlight/dash/bracket are to be replaced this week, then it's back on road for some fun.
Anyone know where to get jack-up kits from locally?
-
Bloke with the stick
By local, do you mean Aus or Canberra?
-
Bloke with the stick
By local, do you mean Aus or Canberra?
-
ASF Premium Full Member
can i get a closeup of the blinkers u rigged up
should run the napoleans under the bars, looks all tucked up that way
(i didnt have too many troubles seeing out of them on the SV)
-
ASF Premium Full Member
can i get a closeup of the blinkers u rigged up
should run the napoleans under the bars, looks all tucked up that way
(i didnt have too many troubles seeing out of them on the SV)
-
The jack-up kits would have to be Aus, CBR wouldn't have anything. Are the dogbones shortened to raise the height? If so can the existing ones be cut and shut? or wouldn't it be strong enough?
Also I can only get 27" wide bars in CBR, so if anyone knows where to get 30"+ wide bars, but they need to be standard "water pipe" bars in order to fit the mirrors/indicators.
I had 2 new hollow bolts made up, to replace the bolts that came with the mirrors, no heads on them, and they are the same thread size as the indicators. I got a coupls of 2 cm long nuts and joined them all up.
I'll post a pick of them apart and assembled tomorrow.
If I run the mirrors under the bars I have to turn my head to see them, whereas I don't as they are, they also reduce the likelihood of some prat walking past and knocking the indicators.
-
The jack-up kits would have to be Aus, CBR wouldn't have anything. Are the dogbones shortened to raise the height? If so can the existing ones be cut and shut? or wouldn't it be strong enough?
Also I can only get 27" wide bars in CBR, so if anyone knows where to get 30"+ wide bars, but they need to be standard "water pipe" bars in order to fit the mirrors/indicators.
I had 2 new hollow bolts made up, to replace the bolts that came with the mirrors, no heads on them, and they are the same thread size as the indicators. I got a coupls of 2 cm long nuts and joined them all up.
I'll post a pick of them apart and assembled tomorrow.
If I run the mirrors under the bars I have to turn my head to see them, whereas I don't as they are, they also reduce the likelihood of some prat walking past and knocking the indicators.
-
Bloke with the stick
Chalky. Go to the parts page of this website and check out TEAM DAYV-BOY. He does lift kits as far as I remember.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules