You have my number
Printable View
almost ready to join all the pieces for the swing arm pivot mounts on the jig......
had to have a look at what it will look like fitted out tho.....
I think a little bit of wee came out....
And yes the handles are the center carrier out of z9 disk brake disk.....
http://i1136.photobucket.com/albums/...psxc7x4v3o.jpg
http://i1136.photobucket.com/albums/...psp7qdoco6.jpg
http://i1136.photobucket.com/albums/...psq1obfuq7.jpg
Mate, I'd just have that on display in my front room, regadless of what it was supposed to do.
Love it.
Geez that's fancy lookin', You sure you know what to do with them ? heh hehe heh
measure and correction are to very different animals so as I have fuck all chance of one I have given
very little thought to the other. Verification on the other hand is very much the catch call for the final
assembly then welding sequence...... I still have to dowel the base plates when a mag base drill turns up,
but apart from that and some test welds, clamp making etc I think a day with two blokes should see it finished
Thought about Tig-brazing it to minimise distortion?
Yes, actually gone as far as to test some silicon bronze tig brazing. In two minds as yet,
cant see how it will pull any less and that is more of a concern than distortion. Tho
I recon I was over 30% less amps to weld the same test piece then with er70s-2 steel.
Thing is I don't know if this is the job to test how the braze comperes to steel in strength terms
as these sections are the datum for the whole process and will ultimately be required to transfer
large forces.
btw I personally think these look way better as a pair......
http://i1136.photobucket.com/albums/...psuozcvqjx.jpg
http://i1136.photobucket.com/albums/...psr47jxtav.jpg
http://i1136.photobucket.com/albums/...psgbaw2pus.jpg
nice work mate ,did you screw cut those threads
The amount of force you're going to apply isn't going to be enough to make the bronze move... It's pretty clear you've designed for deflection rather than to yield strengths. Should pull less than normal tigging - brazing has always been the way to go for minimum movement.
kinda agree, still with a upwards of 20 ton porta power levering of the front of a frame it still makes my arse pucker
on using a new technic on a vital part I only get one chance at after its eaten a few 100 hours.......
Its still a close call even tho yield strength is between a 1/3 and 1/2 less than steel but your correct I designed as much
of this out as I could. mind you this design is still all just by eye and a stab in the dark..
Many hours later, one z swing arm with about 20 year old
power coat. 5 treatments of striper, wire bush and scrapper.
Then blasted and etch primed all pretty like ready for paint.
I hate powder coat if u ever have to work on something,
fucking horrible stuff.
http://i1136.photobucket.com/albums/...psv6hyaixg.jpg
http://i1136.photobucket.com/albums/...psohw3hywy.jpg
So I find myself waiting for some parts to come in
and nothing to do on a Saturday night. Fixed that problem
by drinking and tooling around. One fix was to actually fix
something in the shop. The 8" bench grinder was set up
with the linisher one side and a buff the other. Problem
being the polishing of parts IMO should only involve the removal
of my pants and not shinny metal...... Ages ago I took the wire
wheel of the 6" grinder to install a wheel just for carbide tools and
tungstens. The wire wheel tho had proved very useful and I missed using
it. Solution, cut up the buff adaptor so I keep the left hand thread. I had
made spacers back in the day to fit said wire wheel to the 6" grinder, drilled to
suit the 16mm shaft. I thought some extra width would come in handy. So
I turned down a 16 mm bolt I found in the misc bolt bin. Join the two
with hot metal and a spacer later I have was done. A spot of nut lock on the 16mm
nut as the grinder thread is left hand on that side for a reason and I was done.
Warning ffs anyone that uses wire wheels on anything wear your eye protection......
I personally know someone that has had a piece of wire from his eye. He kept his sight
but the story of being fully lucid as they pulled it out his eye, and as I have in the past
removed bits of javelin like thin horribly painful bits of evil from my flesh I can only recommend
safe practice....... So things in the workshop are not so forgiving.......
http://i1136.photobucket.com/albums/...ps7ygareuk.jpg
http://i1136.photobucket.com/albums/...pshng1k6n8.jpg
Wire wheels are awesome, I had one on the angle grinder the other day to clean up a ratty expanson chamber.
Eye protection is essential as you've said mate, hell I even had my young fellas wear safety glasses even though they were watching from several metres away.
Linisher is so usefull, I must try and get one!!
I got an Abbott n Ashby one last year for $380 ish including the Linisher. Single handedly the most used tool in the shed. The wire wheel is ace for cleaning bolts, but i recommend using pliers to hold them. Sucks balls big time when ya finger runs into the wirewheel.
I changed my std linisher into this one via a kit
http://i1136.photobucket.com/albums/...psfca4kj1r.jpg
And this is the 6", white for high speed steel, green for carbide and tungsten.
If I catch anyone using anything else on those wheels I'll break their fingers.....
http://i1136.photobucket.com/albums/...pspdk5oqcm.jpg
Imma do my best to jam some aluminum cans in there......
Hahahahahaha I know how much it shits me having to dress the stones on the grinder at work because some bright cunt has decided to 'clean' an oxy or mig tip on it......
Hence why I have my own workshop......
I don't share well....
So there I was partaking in my
Bi-yearly grass mowering. When in a shower of glowing hot metal my cutter deck belt tensioning pulley decided that 30years hard time was more than enough. It was found dead on the seen. It's roller bearings lifeless stained blue, like still warm carcasses ready to rot in the hot sun. Testament to the shear vicious ruthlessness of the dark overlord "friction"......... Maters only darkened when spares, money and time were found somewhat wanting when asked to once more go into the breach and this my dear friends brings us to the point of this story...... Necessity is indeed the mother of all invention.......
http://i1136.photobucket.com/albums/...ps8ycqms2y.jpg
Fucking 'ell! I just replaced the bearing on mine, where as you make yours a race version.
Trust me si if I could that's exactly what I would have done,
Thing was just to far gone, the pulley itself collapsed whileknocking
the barrings out forcing my hand. The mower is a 30 + year old diesel kobota
held together with a unwillingness to die. I never care for it, never spend money or time
on it, so this was a welcome change
I get stressed if I don't mow mine once a week.
Twice a week keeps it tidy.
free time in the shop for some more work on my plans for the work space, it is
never a bad idea to revisit areas you thought were done. As your work evolves
so should your workspace....
The bench that sat next to the pillar drill got used mostly to store all the shit I didn't know
what to do with, so got abrasive on its arse and cleaned up the act.
http://i1136.photobucket.com/albums/...psofbgpi0b.jpg
http://i1136.photobucket.com/albums/...ps5np7rb3w.jpg
When does the bed move in?
well getting close to my big japan trip so projects have been mostly put on hold
but still doing some bibs and bobs in the work shop upgrade
the fab area steel rack is getting a rebuild, white board and ben 10 curtains are gone as is the old shelves
http://i1136.photobucket.com/albums/...ps0otxdi7k.jpg
http://i1136.photobucket.com/albums/...pswnwgvyby.jpg
the clean area for the bead blaster and the final home for the hydroblaster is moving ahead as well
left over 16mm ply from a job $0, hat section $7 by 6 mtrs, 25x20 aluminium angle fuck all,
all up both this and the same style wall in the fab area is costing me about $50 sweeeeettttt....
http://i1136.photobucket.com/albums/...psnsnk06ay.jpg
http://i1136.photobucket.com/albums/...ps22cqsib7.jpg
http://i1136.photobucket.com/albums/...ps54fdaxwu.jpg