Page 2 of 10 FirstFirst 1234 ... LastLast
Results 21 to 40 of 182

Thread: 2006 R1 buld - long time between drinks ;)

  1. #21
    Weekend Warrior
    Join Date
    Dec 2009
    Location
    Palmwoods, QLD, Australia.
    Posts
    249
    Absolutely belting along with this build - nice work.

  2. #22
    ASF Premium Full Member LKC73's Avatar
    Join Date
    Nov 2007
    Location
    Sydney, NSW, Australia.
    Posts
    1,507
    Just a bit more done towards getting this thing running again.

    I bought 09 FZ1 throttle cables as they are longer than stock R1 units. This will suite the risers and bar set up we all want.


    Refitted the throttle bodies after the cables attached. Airbox back in place.


    While mucking around, I removed the bars and cleared out the forks for new risers to be installed.
    I'm planning on using low rise fat bars for this build.


    Top part of the bike is just about ready to go. Radiator next and new discs and some lines and we are almost ready for rego.
    Last edited by LKC73; 19-07-2017 at 08:10 PM.
    Monster GSXR 7/11 RIP!
    Raven R1 Demon.
    K7 750 German Style (under construction)

  3. #23
    ASF Standard Full Member Bob's Avatar
    Join Date
    Nov 2008
    Location
    Mt Cotton, Qld, Australia.
    Posts
    2,343
    Coming along great bud
    Ladies and Gentelmen, take my advise. "Pull down your pants and slide on the ice."

  4. #24
    Tyre destroying, mad bastard menace
    Join Date
    Dec 2006
    Location
    Brisvegas
    Posts
    4,914
    Need to start pulling the broken parts off the R1 this weekend and assess where we are on it but should be mostly all good

  5. #25
    ASF Premium Full Member LKC73's Avatar
    Join Date
    Nov 2007
    Location
    Sydney, NSW, Australia.
    Posts
    1,507
    Jules, as long as it isn't as bad as mine was you'll be laughing. I'm still waiting on more parts to arrive and my next pay to order more just to get this thing running. But it will get there.
    Monster GSXR 7/11 RIP!
    Raven R1 Demon.
    K7 750 German Style (under construction)

  6. #26
    ASF Premium Full Member LKC73's Avatar
    Join Date
    Nov 2007
    Location
    Sydney, NSW, Australia.
    Posts
    1,507
    Small update, radiator arrived and all fitted up. Just waiting on a few more parts still!
    I have the header pipe back on as well and small bits and shits.



    Last edited by LKC73; 19-07-2017 at 08:11 PM.
    Monster GSXR 7/11 RIP!
    Raven R1 Demon.
    K7 750 German Style (under construction)

  7. #27
    Tyre destroying, mad bastard menace
    Join Date
    Dec 2006
    Location
    Brisvegas
    Posts
    4,914
    What headlight are you running on it?

    Keeping the stock tail?

  8. #28
    ASF Premium Full Member LKC73's Avatar
    Join Date
    Nov 2007
    Location
    Sydney, NSW, Australia.
    Posts
    1,507
    Quote Originally Posted by wackyrider View Post
    What headlight are you running on it?

    Keeping the stock tail?
    I actually have a wave light like the 7/11 and will be ordering a mask soon.
    The tail will be changed but only after rego is on the bike.


    Parts I do need is a Right foot bracket, indicator's for the front bars and risers and a front disc.
    Monster GSXR 7/11 RIP!
    Raven R1 Demon.
    K7 750 German Style (under construction)

  9. #29
    ASF Premium Full Member LKC73's Avatar
    Join Date
    Nov 2007
    Location
    Sydney, NSW, Australia.
    Posts
    1,507
    So I have all the stuff I need now to kick this thing in the guts and see if it'll run.
    I also got my bars and risers so they'll be installed over the weekend as well.
    If I'm game, I'll video the first fire-up of the R1 after I prime it.
    Monster GSXR 7/11 RIP!
    Raven R1 Demon.
    K7 750 German Style (under construction)

  10. #30
    ASF Premium Full Member LKC73's Avatar
    Join Date
    Nov 2007
    Location
    Sydney, NSW, Australia.
    Posts
    1,507
    So last night I installed the risers and bars. I also got my new headlight and will make the mount for that.
    In the pictures you can see an idea for the dash and where I am thinking of mounting it.
    I'll be making a fibreglass bolt on one to see how I like it. Sitting on the bike it gives great view of the dash there.







    Last edited by LKC73; 19-07-2017 at 08:13 PM.
    Monster GSXR 7/11 RIP!
    Raven R1 Demon.
    K7 750 German Style (under construction)

  11. #31
    ASF Premium Full Member LKC73's Avatar
    Join Date
    Nov 2007
    Location
    Sydney, NSW, Australia.
    Posts
    1,507
    So after I have primed it and built up some oil pressure, I installed the pugs and filled it with water and fired it up!
    HOORAY it started, those of you on facebook would have seen it live last night.

    Sad news is, I had to replace 2 water hose's and repair a water pipe and replace one of the water "O" rings.
    But besides this, It started with very little effort, showed no faults on the dash board and idled super some.

    Next I set out to put the switch blocks on and sort out some wiring routes.





    Last edited by LKC73; 19-07-2017 at 08:15 PM.
    Monster GSXR 7/11 RIP!
    Raven R1 Demon.
    K7 750 German Style (under construction)

  12. #32
    Tyre destroying, mad bastard menace
    Join Date
    Dec 2006
    Location
    Brisvegas
    Posts
    4,914
    If you end up mounting the gauge ont he tank, I might need to have a chat with you...

  13. #33
    Tyre destroying, mad bastard menace
    Join Date
    Apr 2007
    Location
    ipswich qld Australia
    Posts
    4,858
    Blog Entries
    1
    I too think the gauge on the tank is a hot idea, it cleans up the bars for that striped street monster look
    be cool if you cut down the factory housing and move the read outs in relation to the tach, to be honest
    it wouldn't be worth the effort just thought it was a cool idea with a custom bezel
    whole build is a cool bike

  14. #34
    ASF Premium Full Member LKC73's Avatar
    Join Date
    Nov 2007
    Location
    Sydney, NSW, Australia.
    Posts
    1,507
    Jule's, It will be there mate, and I will be making a mould to install as a bolt on unit. If your interested in this idea, Message me if your keen.
    Monster GSXR 7/11 RIP!
    Raven R1 Demon.
    K7 750 German Style (under construction)

  15. #35
    ASF Premium Full Member LKC73's Avatar
    Join Date
    Nov 2007
    Location
    Sydney, NSW, Australia.
    Posts
    1,507

    Cool

    So only been doing little things for the time being. Christmas around the corner and other things to pay for this has now slowed down. I have a few things to work on while I wait.


    Indicator brackets made, only raw in this picture but they will be tidier and painted black.



    Again with the headlight bracket in raw and yet to be painted and maybe narrowed a bit.

    I am currently working on the gauge mount for the tank, pictures to come later if it works
    Last edited by LKC73; 19-07-2017 at 08:27 PM.
    Monster GSXR 7/11 RIP!
    Raven R1 Demon.
    K7 750 German Style (under construction)

  16. #36
    Weekend Warrior
    Join Date
    Dec 2009
    Location
    Palmwoods, QLD, Australia.
    Posts
    249
    Looking good.

    That casting seam around the lower tripleclamp looks arse - pull the front end off and buff the seam off the lower, it makes it look liks a billet tripleclamp. Worth doing on a fighter because the triples are out there on display.

  17. #37
    ASF Premium Full Member LKC73's Avatar
    Join Date
    Nov 2007
    Location
    Sydney, NSW, Australia.
    Posts
    1,507
    Quote Originally Posted by The Phantom View Post
    Looking good.

    That casting seam around the lower tripleclamp looks arse - pull the front end off and buff the seam off the lower, it makes it look liks a billet tripleclamp. Worth doing on a fighter because the triples are out there on display.
    Yep my thoughts too, was going to paint it black to hide it even more. Just setting everything up for now so will pull it down once its sorted.
    Monster GSXR 7/11 RIP!
    Raven R1 Demon.
    K7 750 German Style (under construction)

  18. #38
    Weekend Warrior
    Join Date
    Dec 2009
    Location
    Palmwoods, QLD, Australia.
    Posts
    249
    Awesome

  19. #39
    ASF Premium Full Member LKC73's Avatar
    Join Date
    Nov 2007
    Location
    Sydney, NSW, Australia.
    Posts
    1,507
    A few weeks on and I have carried out some more small works.
    Removed the bottom triple clamp and smoothed all seem lines off it and gave it a satin black finish.



    I also kept going with the tank dash mount. Its been glassed and all wires are run up through the tank cover.
    I just need to do a final filler to fill some low points and then I'll paint it black along with the tank cover.



    I have also got a new rearsets but didn't get around to setting them up.
    Last edited by LKC73; 19-07-2017 at 08:29 PM.
    Monster GSXR 7/11 RIP!
    Raven R1 Demon.
    K7 750 German Style (under construction)

  20. #40
    Bloke with the stick Gix11's Avatar
    Join Date
    Jun 2003
    Location
    Gold Coast, Queensland, Australia
    Posts
    17,574
    Blog Entries
    34
    Cool! I'm liking it.

Page 2 of 10 FirstFirst 1234 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •