PDA

View Full Version : rexies shed clearance


Zed14
30-08-2010, 03:04 PM
i am selling some stuff i dont use as much as i would like. my lathe, mill and 3 project bikes i just dont have time for. first is the hafco hm30 mill drill. it is in good cond mostly used for drilling. comes with two vices one large swivel. 300mm rotary table and two clamp sets one for mill table and one for rotary table. a set of collets and end mills. and some billet pieces. 2400.00 http://www.asfphotos.com/upload/1283161926.jpg


http://www.asfphotos.com/upload/1283211673.jpg


next is the lathe. hafco al330a has 38mm spindle bore 300mm swing and 925mm bed. comes with 3 jaw and 4 jaw chucks. face plate and steadies. drill chuck, and a lot of cutting tools some with inserts and a lot of steel ones. also some round stock alloy. 2500.00http://www.asfphotos.com/upload/1283233395.jpg


http://www.asfphotos.com/upload/1283200713.jpg


http://www.asfphotos.com/upload/1283147989.jpg
if any questions call zed on 0416019455. pick up from grafton. i can lift onto trailer or ute.
latheboy
31-08-2010, 01:19 PM
"i can lift onto trailer or ute"
You must be strong as fuck:D
Zed14
31-08-2010, 03:13 PM
very
mozza
31-08-2010, 03:50 PM
what are the bikes ??
Zed14
31-08-2010, 05:26 PM
they are in the bikes for sale section.
fimpBIKES
31-08-2010, 07:27 PM
wish i could grab those of you mate, but after talking to the fuckin council yesterday i'll be lucky to get a 2 car garage out of them [xx(]
Shadowzone
31-08-2010, 08:38 PM
quote:Originally posted by fimpBIKES

wish i could grab those of you mate, but after talking to the fuckin council yesterday i'll be lucky to get a 2 car garage out of them [xx(]


You deo know its always easier to get stuff approved AFTER it's installed don't you. occasionally it gets removed but mostly approved if its already there.

And if your council subbies out the building approvals to private companies like most of them in Qld do then I would do whatever you wanted then apply for aproval once its in. The private mobs will happily approve shit in retrospect and it only costs a few more $$$ than the fucking around prior approval process.
Hagarr
31-08-2010, 10:14 PM
If you want to sell things seperately I'll take the rotary table!
Zed14
01-09-2010, 06:30 AM
Dont want to seperate them . Will sell lathe with tools and accessories and same with the mill.
Zed14
01-09-2010, 06:33 AM
Tooling accessories are the most expensive items.
xa-mont
01-09-2010, 09:42 AM
why is it that i am not rich and dont have a shed????

I hate you!
JackTar
01-09-2010, 01:53 PM
quote:Originally posted by xa-mont

why is it that i am not rich and dont have a shed????



Only you can answer this question.
xa-mont
01-09-2010, 02:22 PM
it was more of a hypothetical... i know the answer... i just dont like it!
Zed14
27-09-2010, 06:44 PM
lathe sold mill still for sale bring 2000.00 and take it away no offers.
Hagarr
27-09-2010, 07:53 PM
quote:If you want to sell things seperately I'll take the rotary table!